The MAZDA Brazed Radiator is installed in a different way
1. Single pipe series: the single pipe series is characterized by low material usage, relatively weak labor intensity and shorter modification time. The water of the whole system first passed through the first group of MAZDA Brazed Radiator, then the second group, the third group... So the water temperature is decreasing in tandem order. Under the same conditions, the temperature of the first two sets of heating can be over 2 degrees in the room.
2, the single pipe series jumper type technical transformation: in order to adjust the water temperature of a single set of heating, the MAZDA Brazed Radiator in and out of the gate of the front-end must increase the by-pass valve, some with the 3-way regulating valve, also some use three gate valves. The single-string system is useless, and the shutdown of a set of central heating will cause the system to break off immediately, and the other heat will not be heated. Moreover, the MAZDA Brazed Radiators need to be configured in a single pipe series. In order to meet the needs of the system circulation, the director of this heating system needs to be relatively thick.
3, parallel vision system: cheng parallel process pipeline is the feature of the trip is shorter, each set of MAZDA Brazed Radiator can be controlled separately, the system of water balance a single pipe series will be greatly improved, but the system still has some limitations. MAZDA Brazed Radiator water flow is different in each group, the front-end MAZDA Brazed Radiator backwater because near main line, faster, and then the backwater is slower, may cause at the end of the heat is not hot or not hot enough. Solution is through the valve adjustment to solve the problem, the system working status of the front-end heating return valve, in turn, was a little off, to ensure that the system balance, let end heating heat up slowly.
4. Parallel system in parallel: the same process system is characterized by the same characteristics as the parallel process. But has difference in operation principle, in simple terms, is called for, to return to the first is the front end of the first group of MAZDA Brazed Radiator backwater temporarily not to the main loop, but continue to go down, connect the next set of MAZDA Brazed Radiator return pipe, so on... Pull a backwater line from the end MAZDA Brazed Radiator and return to the main pipe back to the water pipe. The water flow of each group of MAZDA Brazed Radiator is basically the same, and the system is very balanced. Arguably the best way to balance the hydraulic system.
5, octopus type piping system: boiler import and export through water segregator and Siamese and each group respectively MAZDA Brazed Radiator connected in parallel, the parallel pipeline hydraulic balance between on the manifold valve adjusted to balance the loop resistance, can be divided into room temperature control. Hot water pipes are usually PEX or XPAP plastic pipes, which are laid on the floor, which is a beautiful way to connect, but more cost.
Installation of MAZDA Brazed Radiator:
1, the need to design good installation plan ahead of time, by a professional MAZDA Brazed Radiator fin installation company is responsible for the design, based on the characteristics of their own family, heating demand, decorate a style, such as specific heating scheme is given, including the MAZDA Brazed Radiator fin style, color, group number, location, duration, etc.
2. The installation position of MAZDA Brazed Radiator, the general principle of the installation position of MAZDA Brazed Radiator is the window, the window side, no matter, inside.
3, the economy into consideration, the north MAZDA Brazed Radiator fin system being central heating, each group of MAZDA Brazed Radiator fin pipe is much by introducing indoor, outdoor and so on under the wave window is also a way of saving pipe. And northern region for household heating, MAZDA Brazed Radiator fin pipe all emissions indoors, therefore, under the window of the MAZDA Brazed Radiator fin and decorating in the interior wall of the MAZDA Brazed Radiator fin system compared to the pipeline to go a lot more, it also increased the heat loss.
4, the family layout into consideration, the metope of bay window usually belong to not use metope, use this place MAZDA Brazed Radiator fin generally will not affect household decorates pattern, but to consider how the be born curtain processing.
5. Considering the convection effect, in terms of convection effect, the most frequent areas of indoor heat exchange are Windows and doors, so in this sense, the convective circulation under the floating window is the best. But the metope of the window that float window must be exterior wall, when the wall absorbs heat, have some heat loss to go outside space. In the inner wall, there is no problem of heat loss to the outdoors.
