The material of the Condenser is different
Condenser to become the country set up equipment deployment department to promote the promotion of the main Condenser products, is now the highest market share in China's Condenser. After several years of practical use, it was found that the use of steel pipe Condenser in the United States is insufficient, that is, the use of pipe-type Condenser after a period of time, easy to appear in the weld water leakage problems. In order to defend the Condenser of the corruption of the water, have studied all kinds of mediation steps, such as the use of various types of steel tube Condenser anti-corrosion, in the Condenser plus magnesium bar plate protection and so on. So that the original anti-corrosion of the Condenser can produce a passive anti-corrosion.
The difference between the steel material used, the difference in the thickness of the steel, the difference in the manufacturing process, the number of welds, the effect is more resistant to corruption. In detail, the original introduction of the product is composed of two pieces of each 15mm thick steel plate were formed after the completion of the welding, the formation of the first week of the weld, including the top of the head of the Department of the water at the top of the weld.
The Condenser uses a straight tube push inflator to expand the tube so that the aluminum pipe wall and liner have reached plastic deformation, rebound after the close, smooth surface, high dimensional accuracy using a plug assembly can reach 100% The So the production sector does not produce waste to reduce the waste of energy. In addition, the assembly process does not require welding, the Condenser surface without overheating, saving a lot of manpower and energy. In addition, the Condenser does not assemble the required process naked liner, the overall strength is high, will not cause deformation and leakage due to improper installation.
Different parts of the Condenser are connected by welding, welding quality will directly affect the quality of the Condenser and the service life. Welding process is mainly filled with welding and body welding, relatively speaking, the body of the corrosion resistance is good, and there is a uniform welding scar, without grinding; filler welding corrosion resistance is poor, smooth and smooth surface.
In the installation of the Condenser, the need for a lot of pressure or torque. Because the diameter of the radiator table is larger than the diameter of the die, under the action of this pressure or moment, the table of the electronic radiator must be deformed. If the same diameter or larger diameter of the die, mounted on the Condenser, it will lead to the surface of the table and the contact between the surface of the bad, so as not to ensure good heat dissipation.
If the user needs to re-use the Condenser, then we must ensure that the radiator surface surface roughness, parallelism and flatness to meet the requirements, or in operation easily overheating and damage to the device. In particular, water-cooled series of concentrators, before repeated use, be sure to carefully check the deformation of the table, such as had a significant subsidence phenomenon, should be replaced.
In order to ensure good thermal conditions, each die should have a corresponding Condenser to match.
In the modern city career, there is no need to worry about the Condenser heat dissipation, but also to think about the surface of the concentrator wonderful. Is in the scope of the need for the next, in order to promote the domestic consumption of the Condenser made a general dedication. Is the overall situation on the surface of the wonderful, progressive Condenser of the ineffective application rate, for the Condenser section must be power. From the Condenser for the consumer needs of the additional goods - whitewashing, thermal comfort and enjoyment of the three ranges of view.Laser industry developed in addition to the name of the goods outside the structure of the scientific research as a major break The Thus, a co-operative form of heat dissipation (radiation, for flow and preheating) to improve the heat dissipation structure can be well energy-efficient. In the ancient career, the hometown of leisure is summarized in the core of the changing classic. Thus, the diversity of the nominal paint of the Condenser has become a point of cooperation for each business. Practical test confirmed: non-metallic coatings than non-metallic coatings can be improved above 10% of the heat. Inside, with light blue for the highest - 17%. So, non-non-metallic paint a single color, but also deal with the consumer manufacturers "work together" predicament. Because urban public establishments and housing quarters are increasingly taking the form of set warmth, which leads to the measurement of the master is not very convenient. Some users for the conditioning room temperature and window, a total waste of 7% of the total heat. Because, is the Condenser clothes set fire control valve potential is necessary. So that can only be used to enjoy the leisurely comfortable winter, but also adapted to the Ministry of the proposed "household metering, sub-room temperature control," the request, called double-edged sword. Is no response to the surface of the wonderful premise, the Condenser heat function has been promoted for everyone's career has brought great convenience, rich people's daily life, to promote energy-saving environmental protection industry stagnation made a general dedication The
